|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
Advanced Setup�Continued
Maximum Volume
With this preference, you can prevent the volume being set too high by specifying a maximum volume level. The range is from 50 to 99. To specify no maximum volume, select Off.
Power On Volume
HDMI Audio Out
1
RECEIVER
Press the [RECEIVER] button followed by the [SETUP] button. The main menu appears onscreen.
With this preference, you can specify the volume setting to be used each time the AV receiver is turned on. The range is MIN, 1 - 99, MAX. To use the same volume level that was used when the AV receiver was turned off, select Last. The �Power On Volume� cannot be set higher than the �Maximum Volume� setting.
Immediate Display
SETUP
2
Use the Up and Down [ ]/[ ] buttons to select �8. Hardware Setup,� and then press [ENTER]. Use the Up and Down [ ]/[ ] buttons to select �HDMI Audio Out,� and use the Left and Right [ ]/[ ] buttons to select On or Off.
This preference determines whether or not actions, such as selecting an input source, are displayed onscreen. Normal: Select if your TV is 4:3. Wide: Select if your TV is 16:9. Off: Actions not displayed. Even if this preference is set to Normal or Wide, actions are not displayed on the TV or projector while outputting the signals received at COMPONENT VIDEO IN or HDMI IN.
This preference determines whether audio received at the HDMI IN is output by the HDMI OUT. You may want to turn this preference on if your TV is connected to the HDMI OUT and you want to listen to the audio from a component that�s connected to an HDMI IN, through your TV�s speakers. Normally, this should be set to Off. Off: HDMI audio is not output (default). On: HDMI audio is output. With some TVs and input signals, no sound may be output even when this setting is set to On. In these cases, set the connected device�s output to PCM.
Changing the AV Receiver�s ID
1
RECEIVER
Press the [RECEIVER] button followed by the [SETUP] button. The main menu appears onscreen.
SETUP
2
Use the Up and Down [ ]/[ ] buttons to select �8. Hardware Setup,� and then press [ENTER]. Use the Up and Down [ ]/[ ] buttons to select �Remote ID,� and use the Left and Right [ ]/ [ ] buttons to select a value.
Remote ID
With this setting, you can change the AV Receiver�s remote control ID. You may need to change this if the remote controller�s control codes overlap with those of another Onkyo component located in the same room. � If you change the AV receiver�s remote control ID, be sure to set the same ID on both the AV receiver and remote controller (see page 78). The default ID for both is 1.
76
|
|
|
> |
|
